OMRON欧姆龙 ZX-XGC8R 张力传感器-产品快照

产品介绍

OMRON欧姆龙 ZX-XGC8R 张力传感器

ZX-XGC8R 238026 ZX 5015R OMRON Advanced sensors, robotic extension cable 8m ZX-G

OMRON

Advanced sensors, robotic extension cable 8m ZX-G

ZX-GT Laser micrometer Smart laser micrometer • High accuracy: 5 to 10 μm •All surfaces • Long sensing distance: < 500 mm • Line width up to 28 mm • Calculation unit for multiple heads • Fast sampling time: 0.5 ms •PC software for setup Ordering information Sensors TypeOptical system Measuring width Sensing distanceResolutionOutput type Order code Separate type Through-beam28 mm 0 to 500 mm 10 μm NPNZX-GT28S11 PNP ZX-GT28S41 Integrated type 40 mm NPNZX-GT2840S11 PNP ZX-GT2840S41 Controller Power supplyOutput type Order code DCNPNZX-GTC11 PNP ZX-GTC41 Accessories (order separately) Set of interface unit and setup software PCs Output type Order code Calculating units Order code NPN ZX-GIF11A PNP ZX-GIF41A Interface unit(RS-232C/binary output) Power supplyOutput type Order code DCNPNZX-GIF11 PNP ZX-GIF41 Setup software PCs Name Order code Smart monitorGTZX-GSW11 Calculating unitZX-CAL2 Receiver-controller extension cable Cable length Quantity Order code Standard cableFlexible cable 1m1 m ZX-XGC1AZX-XGC1R 2mZX-XGC2AZX-XGC2R 5mZX-XGC5AZX-XGC5R 8mZX-XGC8AZX-XGC8R 20 mZX-XGC20A ZX-XGC20R Up to two extension cables can be connected. However, be sure to limit the total extension cable length between the receiver and the controller to 30 meters (including the receiver cable). 397 ZX-GT Laser micrometer Specifications Sensor Item ZX-GT28S11ZX-GT2840S11ZX-GT28S41ZX-GT2840S41 Output type NPNPNP Appearance Separate type Integrated typeSeparate type Integrated type Light source Visible semiconductor laser diode (wavelength 650 nm, CLASS 1 of EN60825-1/IEC60825-1, CLASS of FDA(21CFR 1040.10 and 1040.11) Measuring width 28 mm Sensing distance0 to 500 mm 40 mm 0 to 500 mm 40 mm Minimum sensing object 0.5 mm dia.*1 Linearity ±0.1% F.S.*2 0.2 mm dia.0.5 mm dia.*10.2 mm dia. Resolution 10 μm (number of process values to average: 16)*3 Temperature characteristic ±0.01% F.S/C*4 Indicators (emitter) Laser ON indicator (green), laser alarm indicator (red) Indicator (receiver) Optical axis setting indicator (green) Laser OFF input/sync inputON: Short-circuited with 0 V or 1.5 V max. OFF: Open (leakage current: 0.1 mA max.) Laser deterioration alarm output NPN open-collector output 30 VDC 20 mA max. Residual voltage 1.2 V max. Power consumption (emitter) 30 mA max. Power supply voltage (emitter) 24 VDC+10%, –15% ripple (p-p) 10% max. Dielectric strength 1,000 VAC, 50/60 Hz for 1 min Insulation resistance 20 M (at 500VDC megger) ON: Short-circuited with power supply voltage or power supply voltage -1.5 V max. OFF: Open (leakage current: 0.1 mA max.) PNP open-collector output 30 VDC 20 mA max. Residual voltage 2 V max. Operating ambient illumination (emitter) Operating ambient illumination (receiver) 3,000 lx (incandescent light) 1,000 lx (incandescent light)*5 Ambient temperatureOperating: 0 to 40°C, storage: –15 to 50°C (with no icing or condensation) Ambient humidity Operating and storage: 35% to 85% (with no condensation) Vibration resistance (durability) 10 to 150 Hz single-amplitude: 0.75 mm for 80 min each in X, Y and Z directions Degree of protectionIEC60529 IP40 Cable length2m Material Case: aluminum die-cast, Lens: glass Weight (packed state)Approx. 550 g Approx. 570 g Approx. 550 g Approx. 570 g AccessoriesLaser warning labels, instruction sheet F.S.: 28 mm measuring range of receiver *1Distance between emitter and receiver: 500 mm, measurement object at 250 mm from receiver. Glass ends of chamfer 0.1 mm or more can be detected in glass edge measurement mode. (at binary level 70%) *2Linearity is given to be a typical error with respect to an ideal straight line when the distance between the emitter and receiver is 100 mm and light is blocked at a distance of 50 mm from the receiver. (On the ZX-GT2840_, the measurement object is measured at a distance of 20 mm from the receiver.) *3The amount of fluctuation (±3 ) in the analog output when the distance between the emitter and receiver is 100 mm and a ZX-GTC_ is connected *4Change in the light cutoff value on one side when the distance between the emitter and receiver is 100 mm and the light is half-cutoff at a distance of 50 mm from the receiver (On the ZX-GT2840_, the measurement object is measured at a distance of 20 mm from the receiver.) *5Standard mode (NORM) used Controller Item ZX-GTC11ZX-GTC41 Output type NPNPNP Measurement cycle*11.5 ms (standard mode (NORM)) 0.5 ms (high-speed mode (FAST))*2 Samples to average 1/2/4/8/16/32/64/128/256/512/1024/2048/4096 Analog output*3 For current output: 4 to 20 mA/F.S., max. load resistance 300  For voltage output: ±4 V, (±5 V, 1 to 5 V*4), output impedance 100  Timing input, bank switching input, zero reset input, reset input HIGH/PASS/LOW Judgment output*5 Sync output*6 ON: short-circuited with 0 V or 1.5 V max. OFF: Open (leakage current: 0.1 mA max.) NPN open-collector output 30 VDC 50 mA max. Residual voltage 1.2 V max. ON: short-circuited with power supply voltage or power supply voltage -1.5 V max. OFF: Open (leakage current: 0.1 mA max.) PNP open-collector output 30 VDC 50 mA max. Residual voltage 2 V max. IndicatorJudgment output indicator: HIGH (orange), PASS (green), LOW (orange) Main display (red) sub-display (yellow) bank 1/2 (orange), zero reset (green) Main functions Number of registered setups 2 banks Measurement mode Interrupted beam width measurement, incident beam width measurement, outer diameter measurement, center position measurement, IC lead pitch, IC lead width judgment, specified edge measurement, wire position measurement, glass edge position measurement Display during measurement Measured value, resolution, threshold, voltage output value, current output value (number of display digits can be changed) Zero reset functions Offset setting of zero reset value, zero reset value memory Hold Sample hold, peak hold, bottom hold, peak-to-peak hold, average hold, delay hold Timer functionsON-delay, OFF-delay, one-shot Adjustment functionsOptical axis adjust mode/light intensityt writing mode, variable binary level, variable edge filter, analog output scaling Calculation2 possible on up to two controllers (calculation Unit ZX-CAL2 is required for connecting controllers to each other.) A-B, A+B, width OtherMeasurementcycle setting, threshold setting, hysteresis setting, initialization, key lock 398 ZX-GT Laser micrometer Item ZX-GTC11 ZX-GTC41 Temperature characteristic ±0.005% F.S./°C Current consumption 150 mA max. (including receiver) Power supply voltage24 VDC+10%, –15% ripple (p-p) 10% max. Dielectric strength 1,000 VAC, 50/60 Hz for min Insulation resistance 20 M (at 500VDC megger) Ambient temperatureOperating: 0 to 50°C, storage: –15 to 60°C (with no icing or condensation) Ambient humidity Operating and storage: 35% to 85% (with no condensation) Vibration resistance(durability)10 to 150 Hz single-amplitude: 0.35 mm for 80 min each in X, Y and Z directions Degree of protectionIEC60529 IP20 Cable length2m Material Case: PBT (polybutylene terephthalate), cover: Polycarbonate Weight (packed state)Approx. 330 g Accessories Instruction sheet *1The first response time is “measurementcycle x (number of samples to average setting + 1) + 1 ms” max. For the second response time onwards, the specified measurement cycle time is output. *2The response time in the high-speed mode (FAST) for the IC lead pitch and IC lead width judgment modes is 1 ms. *3Current/voltage can be switched using the switch provided on the rear of the Controller. *4Can be set by the analog output scaling function. *5The error (ERR) state is displayed when all HIGH/PASS/LOW outputs turn OFF. *6Normally, wire the sync output wire directly to the emitter's sync input wire and run the controller in the standard mode. On an NPN type controller, use an NPN type emitter, and on a PNP type controller, use a PNP type emitter. Wiring of the sync wires is not required when the controller is run in the high-speed mode. (Note, however, that the controller becomes more susceptible to the influence of ambient light in this case.) Interface unit Item ZX-GIF11/-GIF11AZX-GIF41/-GIF41A Compatible controller ZX-GTC11ZX-GTC41 IndicatorPower ON (green), controller communications (orange), controller communications error (red), RS-232C communications (orange), RS-232C communications error (red), binary output (orange) Communications portRS-232C (9-pin D-sub connector) 12-bit binary output (D11 toD0, GATE) NPN open-collector output 30 VDC 20 mA max. Residual voltage 1.2 V max. PNP open-collector output 30 VDC 20 mA max. Residual voltage 2 V max. Power supply voltageSupplied from controller (power consumption: 60 mA max.) Dielectric strength 1,000 VAC, 50/60 Hz for 1 min Insulation resistance 20 M (at 500VDC megger) Ambient temperatureOperating: 0 to 50°C, storage: –15 to 60°C (with no icing or condensation) Ambient humidity Operating and storage: 35% to 85% (with no condensation) Vibration resistance(durability)10 to 150 Hz single-amplitude: 0.35 mm for 80 min each in X, Y and Z directions Degree of protectionIEC60529 IP20 Cable lengthRS-232C 0.5 m, binary output 2 m Material Case: PBT (polybutylene terephthalate), cover: Polycarbonate Weight (packed state)ZX-GIF_1A: Approx. 550 g ZX-GIF_1: Approx.330 g Accessories ZX-GIF_1A: Setup coftware (CD-ROM), 2 clamps, instruction sheet ZX-GIF_1: 2 clamps, instruction sheet 399

Categories: Monitoring Products Measurement Accessories Advanced Sensors