OMRON欧姆龙 E3X-CN12 电传感器-产品快照

产品介绍

OMRON欧姆龙 E3X-CN12 电传感器

E3X-CN12 336331 OMRON Photoelectric sensor, 1h connection Cable Slave E3X-DA-N

OMRON

Photoelectric sensor, 1h connection Cable Slave E3X-DA-N

Ordering information Type Connecting method Inputs/outputs Order code NPN output PNP output Standard models Pre-wired (2 m) 1 output E3NX-CA11 2M E3NX-CA41 2M Wire-saving Connector 1 output E3NX-CA6 E3NX-CA8 Advanced models Pre-wired (2 m) 2 outputs + 1 input E3NX-CA21 2M E3NX-CA51 2M Model for Sensor Communications Unit Connector for Sensor Communications Unit - E3NX-CA0 Specifications Item Type Standard models Advanced models Model for Sensor Communications Unit NPN output E3NX-CA11 E3NX-CA6 E3NX-CA21 E3NX-CA0 PNP output E3NX-CA41 E3NX-CA8 E3NX-CA51 Connecting method Pre-wired Wire-saving Connector Pre-wired Connector for Sensor Communications Unit I/O Outputs 1 output 2 outputs - External input - 1 input Light source (wavelength) White LED (420 to 700 nm) Supply voltage 10 to 30 VDC, including 10% ripple (p-p) Supplied from the connector through the Sensor Communications Unit. Power consumption At Power Supply Voltage of 24 VDC Normal mode: 960 mW max. (Current consumption: 65 mA max.) Eco function ON: 720 mW max. (Current consumption: 30 mA max.) Eco function LO: 800 mW max. (Current consumption: 33 mA max.) Control output Load power supply voltage 30 VDC max., open-collector output - Load current Groups of 1 to 3 Amplifiers: 100 mA max., Groups of 4 to 30 Amplifiers: 20 mA max. Residual voltage At load current of less than 10 mA: 1 V max. At load current of 10 to 100 mA: 2 V max. OFF current 0.1 mA max. Protection circuits Power supply reverse polarity protection, output short-circuit protection, and output reverse polarity protection Power supply reverse polarity protection Sensing method Contrast Mode: Light intensity discrimination for RGB (initial state/after 2-point tuning) (R+G+B light intensity discrimination for 1-point tuning) Color Mode: RGB ratio discrimination Response time Super-high-speed Mode (SHS) Operate or reset: 50 µs (only in Contrast Mode) High-speed Mode (HS) Operate or reset: 250 µs Standard Mode (Stnd) Operate or reset: 1 ms Giga-power Mode (GIGA) Operate or reset: 16 ms Sensitivity adjustment Smart Tuning (2-point tuning, full autotuning, or 1-point tuning (1% to 99%)) or manual adjustment Maximum connectable units 30 Units 30 Units (When connected to OMRON NJ-series Unit) Functions Operation mode Contrast Mode: NO (Light-ON) or NC (Dark-ON) Color Mode: NO (ON for match: ON for same color as registered color) or NC (ON for mismatch: ON for different color from registered color) Timer Select from timer disabled, OFF-delay, ON-delay, one-shot, or ON-delay + OFF-delay timer (Counted by 0.1 s in a range of 0.1 to 0.5 ms, by 0.5 ms for 0.5 to 5 ms, and by 1 ms for 5 to 9999 ms. Default: 10 ms, Error: 0.1 ms) Zero reset Contrast Mode only Negative values can be displayed. (Threshold level is shifted.) Resetting settings Select from initial reset (factory defaults), user reset (saved settings), or bank reset. Eco mode Select from OFF (digital display lit), Eco ON (digital display not lit), and Eco LO (digital display dimmed). Bank switching Select from banks 1 to 8. Power tuning level Set from 100 to 9,999. (The RGB maximum incident level at Smart Tuning is adjusted to the power tuning level.) Output 2 - Normal, error output, AND output, or OR output - External input - Select from input OFF, tuning, full-auto tuning, emission OFF, bank 1 and 2 switching, bank 1 through 8 switching, or zero reset. - Changing the displays Threshold level and incident level, channel number and incident level, RGB display and incident level, or bank display and incident level *1 The E3NW-ECT Sensor Communications Unit can be used, but the E3NW-CRT/CCL, E3X-DRT21-S, and E3X-CRT/ECT Sensor Communications Units cannot be used. *2 Two sensor outputs are allocated in the programmable logic controller (PLC) I/O table. PLC operation via Communications Unit enables reading detected values and changing settings. *3 The following details apply to the input. Contact input (relay or switch) Non-contact input (transistor) NPN ON: Shorted to 0 V (Sourcing current: 2 mA max.). OFF: Open or shorted to Vcc. ON: 1.5 V max. (Sourcing current: 2 mA max.) OFF: Vcc - 1.5 V to Vcc (Leakage current: 0.1 mA max.) PNP ON: Shorted to Vcc (Sinking current: 3 mA max.). OFF: Open or shorted to 0 V. ON: Vcc - 1.5 V to Vcc (sinking current: 3 mA max.) OFF: 1.5 V max. (Leakage current: 0.1 mA max.) *4 Power consumption At Power Supply Voltage of 10 to 30 VDC Normal mode: 1,080 mW max. (Current consumption: 36 mA max. at 30 VDC, 74 mA max. at 10 VDC) Eco function ON: 840 mW max. (Current consumption: 28 mA max. at 30 VDC, 50mA max. at 10 VDC) Eco function LO: 930 mW max. (Current consumption: 31 mA max. at 30 VDC, 55 mA max. at 10 VDC) *5 The mutual interference prevention function is disabled if the detection mode is set to Super-high-speed Mode. *6 The bank is not reset by the user reset function or saved by the user save function. Recommended fiber heads Sensing method Sensing direction Size Order code Reflective Right-angle M6 E32-C91N 2M Through-beam (Grooved type) Array 10 mm E32-G16 2M Fiber amplifier connectors Type Cable length No. of conductors Applicable fiber amplifier units Order code Master connector 2 m 3 E3NX-CA6 E3NX-CA8 E3X-CN11 Slave connector 1 E3X-CN12 1. A Sensor Communications Unit is required if you want to use the Fiber Amplifier Unit on a network.

Categories: Fiber Optic Sensors Optical E3X