Schneider施耐德 ATV12P075M3 逆变器施耐德-产品快照

产品介绍

Schneider施耐德 ATV12P075M3 逆变器施耐德

ATV12P075M3 | Schneider | variable speed drive ATV12 - 0.75kW - 1hp - 200..240V - 3ph - on base plate

ATV12P075M3

Estimated Lead Time: 3-4 Weeks Manufacturer: Schneider ATV12P075M3 variable speed drive ATV12 - 0.75kW - 1hp - 200..240V - 3ph - on base plate Range of product : Altivar 12 Product or component type : Variable speed drive Product destination : Asynchronous motors Product specific application : Simple machine Assembly style : On base plate Component name : ATV12 Quantity per set : Set of 1 EMC filter : Without EMC filter Built-in fan : Without Network number of phases : Three phase [Us] rated supply voltage : 200...240 V (- 15...10 %) Motor power kW : 0.75 kW Motor power hp : 1 hp Communication port protocol : Modbus Line current : 5.3 A at 240 V 6.3 A at 200 V Speed range : 1...20 Transient overtorque : 150...170 % of nominal motor torque depending on drive rating and type of motor Asynchronous motor control profile : Quadratic voltage/frequency ratio Sensorless flux vector control Voltage/frequency ratio (V/f) IP degree of protection : IP20 without blanking plate on upper part Noise level : 0 dB Complementary Supply frequency : 50/60 Hz (+/- 5 %) Type of connector : 1 RJ45 for Modbus on front face Physical interface : 2-wire RS 485 for Modbus Transmission frame : RTU for Modbus Transmission rate : 38400 bit/s 19200 bit/s 9600 bit/s 4800 bit/s Number of addresses : 1...247 for Modbus Communication service : Read device identification (43) Read/write multiple registers (23), messaging: 4/4 words maximum Write multiple registers (16), messaging: 27 words maximum Write single register (06), messaging: 29 words maximum Read holding registers (03), messaging: 29 words maximum Prospective line Isc : <= 5 kA Continuous output current : 4.2 A at 4 kHz Maximum transient current : 6.3 A for 60 s Speed drive output frequency : 0.5...400 Hz Nominal switching frequency : 4 kHz Switching frequency : 4...16 kHz with derating factor 2...16 kHz adjustable Braking torque : Up to 70 % of nominal motor torque without braking resistor Up to 150 % of nominal motor torque with braking resistor at high inertia Motor slip compensation : Adjustable Preset in factory Output voltage : 200...240 V three phase Electrical connection : L1, L2, L3, U, V, W, PA, PC terminal 3.5 mm² (AWG 12) Tightening torque : 0.8 N.m Insulation : Electrical between power and control Supply : Internal supply for logic inputs 24 V DC, voltage limits 20.4...28.8 V, 100 mA for overload and short-circuit protection Internal supply for reference potentiometer 5 V DC, voltage limits 4.75...5.25 V, 10 mA for overload and short-circuit protection Analogue input number : 1 Analogue input type : AI1 configurable voltage 0...5 V, impedance 30 kOhm AI1 configurable voltage 0...10 V, impedance 30 kOhm AI1 configurable current 0...20 mA, impedance 250 Ohm Discrete input number : 4 Discrete input type : (LI1...LI4) programmable, 24 V, voltage limits 18...30 V Discrete input logic : Positive logic (source), 0...< 5 V (state 0), > 11 V (state 1) Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm Sampling duration : < 10 ms for analogue input < 20 ms, tolerance +/- 1 ms for logic input Linearity error : +/- 0.3 % of maximum value for analogue input Analogue output number : 1 Analogue output type : (AO1) software-configurable current, analogue output range 0...20 mA, output impedance 800 Ohm, analogue output resolution 8 bits (AO1) software-configurable voltage, analogue output range 0...10 V, output impedance 470 Ohm, analogue output resolution 8 bits Discrete output number : 2 Discrete output type : (R1A, R1B, R1C) protected relay output 1 C/O (LO+, LO-) logic output Minimum switching current : 5 mA at 24 V DC for logic relay Maximum switching current : 4 A at 30 V DC resistive load cos phi = 1 L/R = 0 ms for logic relay 3 A at 250 V AC resistive load cos phi = 1 L/R = 0 ms for logic relay 2 A at 30 V DC inductive load cos phi = 0.4 L/R = 7 ms for logic relay 2 A at 250 V AC inductive load cos phi = 0.4 L/R = 7 ms for logic relay Acceleration and deceleration ramps : Linear from 0 to 999.9 s S U Braking to standstill : By DC injection, 0.1...30 s Protection type : Thermal motor protection via the drive by continuous calculation of I²t Against input phase loss in three-phase Short-circuit between motor phases Overheating protection Overcurrent between output phases and earth Line supply undervoltage Line supply overvoltage Frequency resolution : Display unit 0.1 Hz Analog input converter A/D, 10 bits Time constant : 20 ms, tolerance +/- 1 ms for reference change Marking : CE Operating position : Vertical +/- 10 degree Height : 143 mm Width : 72 mm Depth : 102.2 mm Product weight : 0.7 kg Environment Electromagnetic compatibility : Voltage dips and interruptions immunity test conforming to EN/IEC 61000-4-11 Surge immunity test (level 3) conforming to EN/IEC 61000-4-5 Radiated radio-frequency electromagnetic field immunity test (level 3) conforming to EN/IEC 61000-4-3 Immunity to conducted disturbances (level 3) conforming to EN/IEC 61000-4-6 Electrostatic discharge immunity test (level 3) conforming to EN/IEC 61000-4-2 Electrical fast transient/burst immunity test (level 4) conforming to EN/IEC 61000-4-4 Electromagnetic emission : Conducted emissions with additional EMC filter, class: environment 2 category C3 conforming to EN/IEC 61800-3 - test level: 4...12 kHz, <= 20 m shielded motor cable Conducted emissions with additional EMC filter, class: environment 1 category C2 conforming to EN/IEC 61800-3 - test level: 4...12 kHz, <= 20 m shielded motor cable Radiated emissions, class: environment 1 category C2 conforming to EN/IEC 61800-3 - test level: 2...16 kHz shielded motor cable Product certifications : CSA C-Tick GOST NOM UL Vibration resistance : 1.5 mm peak to peak (f = 3...13 Hz) drive unmounted on symmetrical DIN rail conforming to EN/IEC 60068-2-6 1 gn (f = 13...200 Hz) conforming to EN/IEC 60068-2-6 Shock resistance : 15 gn for 11 ms conforming to EN/IEC 60068-2-27 Relative humidity : 5...95 % without dripping water conforming to IEC 60068-2-3 5...95 % without condensation conforming to IEC 60068-2-3 Ambient air temperature for storage : -25...70 °C Ambient air temperature for operation : 40...60 °C with current derating 2.2 % per °C -10...40 °C with protective cover from the top of the drive removed Operating altitude : > 1000...3000 m with current derating 1 % per 100 m <= 1000 m without derating Shipping Weight : 1.7 Kg

Inverters Schneider