MRC Bearings 7316PJDE-BRZ 轴承-产品快照

产品介绍

MRC Bearings 7316PJDE-BRZ 轴承

MRC 7316PJDE-BRZ ANGULAR CONTACT BALL BRGS

MRC Bearing

Item Details Manufacturer: MRC Bearing Service Weight: 8.8 lbs. Product Name: 7300PJDE Series 40° Angular Contact Ball Bearing Description: Single Row Angular Contact Bearing, 80 mm ID x 170 mm OD x 39 mm Wide, Open, Standard Precision (ABEC 1), Brass / Bronze Cage, Normal Clearance (C0), 40° Contact Angle Specifications Inch/Metric Metric Bore Bore Type Round Bore I.D. 80 mm O.D. [Min] O.D. [Max] O.D. 170 mm Width [Min] Width [Max] Width 39 mm Enclosure Open Rows of Balls Single Material Steel O.D. Type Straight Bearing Type Angular Contact Precision Standard Radial Internal Clearance Specification Normal Clearance Ambient Temperature Range [Min] Ambient Temperature Range [Max] Ball Material Steel Cage Type Metal Capacity Standard Capacity Contact Angle 40° Guide Type Lubrication Outer Ring Width 39 mm Precision Level Standard (ABEC 1) Preload Level None Seal Material None Seal Type Unsealed Seal Width Dynamic Load Rating 32100 lbf Static Load Rating [Max] 27000 lbf Ball Dia. Bearing Design Bore B Cage Material Brass/Bronze Collar No. Collar O.D. Collar Width Corner Radius [Min] Eccentric Collar Offset Fillet Radius 2 mm Flange O.D. [Max] Flange O.D. Flange Width [Max] Flange Width Flush Ground Housing Shoulder Diameter [Min] Housing Shoulder Diameter [Max] Housing Shoulder Diameter Industry Standard Part # Inner Ring O.D. Inner Ring Offset Inner Ring Width 39 mm Internal Design Limiting Speed Limiting Speed - Grease 3600 rpm Limiting Speed - Oil 4700 rpm Limiting Speed - Sealed Locking Device No Locking Device Lube Hole Center Lubricant Oil Preservative Misalignment Range No. in Set Single Bearing No. of Balls O.D. (B) Outer Ring Outer Ring Inner Diameter Outer Ring Size Peak Running Torque (mg-mm) Peak Starting Torque (mg-mm) Pre Lubricant Preload Amount Radial Internal Clearance Normal Radial Load Rating [Max] Radial Rigidity (lbf/µm) Reference Speed Seal O.D. Seal Protection Width Seating Washer Series Set Screw Offset Set Screw Size Shaft Shoulder Diameter [Min] Shaft Tolerance Snap Ring No Snap Ring Snap Ring O.D. Snap Ring Offset Snap Ring Thickness Special Features Stamping Static Thrust Load Rating [Max] Temperature Range [Min] Temperature Range [Max] 450 °F Use With Product Information General MRC angular contact bearings with a PJ suffix have one heavy race shoulder on the outer ring, opposing one heavy race shoulder and on recessed race shoulder on the inner ring. Because of this construction, it is possible for this bearing to incorporate a greater number of balls than a deep groove nonfilling notch bearing. The combination of maximum ball complement, optimum race groove depth, and the 40° contact angle results in high thrust load carrying capacity. 7000-PJ bearings are particularly suitable for positions where the thrust is always present in one direction. It should not be used where the bearing is subjected to radial load only, or combined radial and thrust load where the radial load is predominant. When heavy thrust must be taken in both directions, and angular contact bearing may be mounted in a duplex arrangement with another angular contact bearing or with a 9000-UP split inner ring bearing. 7000-PJ bearings are available with either peressed brass or machined brass, ball centered cages. The low shoulder diameters on the nonthrust sides of inner and outer rings, combined with large clearances between the land diameters and the cage, allow for large quantities of oil to flow through the bearings. The increased oil flow reduces operating temperature and theoretically increases bearing life. ABEC Grade 3 bore tolerances reduce the range of interference fits between the shaft and bearing bore. These tighter tolerances result in closer control of preload and minimize the risk of thermal runaway. 7300-PJ and PJD Series bearings are used for very heavy one-directional thrust loads or combined radial and thrust loads where thrust is predominant. MRC angular contact bearings with a PJ suffix have one heavy race shoulder on the outer ring, opposing one heavy race shoulder and on recessed race shoulder on the inner ring. Because of this construction, it is possible for this bearing to incorporate a greater number of balls than a deep groove nonfilling notch bearing. The combination of maximum ball complement, optimum race groove depth, and the 40° contact angle results in high thrust load carrying capacity. 7000-PJ bearings are particularly suitable for positions where the thrust is always present in one direction. It should not be used where the bearing is subjected to radial load only, or combined radial and thrust load where the radial load is predominant. When heavy thrust must be taken in both directions, and angular contact bearing may be mounted in a duplex arrangement with another angular contact bearing or with a 9000-UP split inner ring bearing. 7000-PJ bearings are available with either peressed brass or machined brass, ball centered cages. The low shoulder diameters on the nonthrust sides of inner and outer rings, combined with large clearances between the land diameters and the cage, allow for large quantities of oil to flow through the bearings. The increased oil flow reduces operating temperature and theoretically increases bearing life. ABEC Grade 3 bore tolerances reduce the range of interference fits between the shaft and bearing bore. These tighter tolerances result in closer control of preload and minimize the risk of thermal runaway. 7300-PJ and PJD Series bearings are used for very heavy one-directional thrust loads or combined radial and thrust loads where thrust is predominant.

BRAND: MRC Bearing | MODEL: 7316PJDE-BRZ | CONDITION: NEW | SKU: 1133440

Bearings