EZPZ23-HR1 步进驱动器

EZPZ23-HR1 步进驱动器-产品快照

品牌:
型号:
EZPZ23-HR1

* 所有产品信息均源于第三方公开数据或用户上传,工业链仅整合供参考,真实价格货期请联系供应商确认.


供应商名称 电话 备注
暂无展示,可咨询在线客服 400-811-6961 微信咨询,cs10@gchane.com , QQ1653501665

供应商或现货商入驻,请点击>>

产品介绍

EZPZ23-HR1 步进驱动器

AllMotion: Servo Drive (EZPZ23-HR1 Series)

AllMotion: Servo Drive ( EZPZ23-HR1 S eries) The EZ Piezo Servo was designed to allow the rapid implementation of Position Control using the Nanomotion** HR1/HR2/HR4/ST1 or similar motor. The fully intelligent controllers measure just 2.25 " x 2.25 ". The Nanomotion** HR1/HR2/HR4 Motor, 9pin DSUB connector plugs directly into the Controller. A single 4 wire bus, containing 2 power wires and two communications wires, links up to 16 such Piezo motor controllers in a daisy chain. (See Wiring Diagram ). Commands can be issued from any serial terminal program (such as HyperTerminal ) or from the EZServo /Stepper Windows application. The Commands are intuitive and simple. For example, the command A10000 will move the Servo motor to A bsolute position 10000 . (This communications protocol is compatible with devices that use the Cavro DT or OEM protocol.) The EZServo is also capable of stand-alone operation with no connection to a PC. It can be set to execute a preset string of commands upon power up (i.e., only power is required in this mode). The Commands i n clude nested loops and execution halt pending a switch closure, which is useful in stand-alone applications. Using our Starter Kits , a first time user is able to make The HR1/HR2/HR4/ST1 Piezo Motor servo intelligently in less than half an hour. (See Wiring Diagram .) Features Single 4 wire bus linking up to 16 Stepper/Servo motors HR1/HR2/HR4/ST1 Motor plugs directly into the driver controller 12V 2A Supply Voltage RS232, RS485 or USB based Communications 4 Quadrant Operation On Board EEPROM For User Program storage Stand alone operation with no connection to a PC Execution Halt/Branch pending switch closure Pre-wired for OptoSwitch inputs (see wiring diagram) Position Velocity and Torque modes Industry standard communications protocol Homes to an Opto or Encoder Index with a single command Fully programmable ramps and speeds Quadrature encoder based feedback for position mode Velocity mode possible with only Hall sensors for feedback Switch selectable device address Software selectable max currents 4MHz max encoder frequency Two 1 Amp On Off Drivers included Optional Step and Direction mode, 4MHz Step Frequency 4 ADC Inputs Halt / Branch on ADC Value Support Links EZServo Wiring Diagram EZServo Command Set EZServo Windows Application EZ Starter Kit Instructions EZPZ 3D CAD Files EZPZ on 3DContentCentral EZPZ-HR Data sheet AllMotion: Servo Drive ( EZPZ23-HR1 S eries) The EZ Piezo Servo was designed to allow the rapid implementation of Position Control using the Nanomotion** HR1/HR2/HR4/ST1 or similar motor. The fully intelligent controllers measure just 2.25 " x 2.25 ". The Nanomotion** HR1/HR2/HR4 Motor, 9pin DSUB connector plugs directly into the Controller. A single 4 wire bus, containing 2 power wires and two communications wires, links up to 16 such Piezo motor controllers in a daisy chain. (See Wiring Diagram ). Commands can be issued from any serial terminal program (such as HyperTerminal ) or from the EZServo /Stepper Windows application. The Commands are intuitive and simple. For example, the command A10000 will move the Servo motor to A bsolute position 10000 . (This communications protocol is compatible with devices that use the Cavro DT or OEM protocol.) The EZServo is also capable of stand-alone operation with no connection to a PC. It can be set to execute a preset string of commands upon power up (i.e., only power is required in this mode). The Commands i n clude nested loops and execution halt pending a switch closure, which is useful in stand-alone applications. Using our Starter Kits , a first time user is able to make The HR1/HR2/HR4/ST1 Piezo Motor servo intelligently in less than half an hour. (See Wiring Diagram .) Features Single 4 wire bus linking up to 16 Stepper/Servo motors HR1/HR2/HR4/ST1 Motor plugs directly into the driver controller 12V 2A Supply Voltage RS232, RS485 or USB based Communications 4 Quadrant Operation On Board EEPROM For User Program storage Stand alone operation with no connection to a PC Execution Halt/Branch pending switch closure Pre-wired for OptoSwitch inputs (see wiring diagram) Position Velocity and Torque modes Industry standard communications protocol Homes to an Opto or Encoder Index with a single command Fully programmable ramps and speeds Quadrature encoder based feedback for position mode Velocity mode possible with only Hall sensors for feedback Switch selectable device address Software selectable max currents 4MHz max encoder frequency Two 1 Amp On Off Drivers included Optional Step and Direction mode, 4MHz Step Frequency 4 ADC Inputs Halt / Branch on ADC Value AllMotion: Servo Drive ( EZPZ23-HR1 S eries) The EZ Piezo Servo was designed to allow the rapid implementation of Position Control using the Nanomotion** HR1/HR2/HR4/ST1 or similar motor. The fully intelligent controllers measure just 2.25 " x 2.25 ". The Nanomotion** HR1/HR2/HR4 Motor, 9pin DSUB connector plugs directly into the Controller. A single 4 wire bus, containing 2 power wires and two communications wires, links up to 16 such Piezo motor controllers in a daisy chain. (See Wiring Diagram ). Commands can be issued from any serial terminal program (such as HyperTerminal ) or from the EZServo /Stepper Windows application. The Commands are intuitive and simple. For example, the command A10000 will move the Servo motor to A bsolute position 10000 . (This communications protocol is compatible with devices that use the Cavro DT or OEM protocol.) The EZServo is also capable of stand-alone operation with no connection to a PC. It can be set to execute a preset string of commands upon power up (i.e., only power is required in this mode). The Commands i n clude nested loops and execution halt pending a switch closure, which is useful in stand-alone applications. Using our Starter Kits , a first time user is able to make The HR1/HR2/HR4/ST1 Piezo Motor servo intelligently in less than half an hour. (See Wiring Diagram .) Single 4 wire bus linking up to 16 Stepper/Servo motors HR1/HR2/HR4/ST1 Motor plugs directly into the driver controller 12V 2A Supply Voltage RS232, RS485 or USB based Communications 4 Quadrant Operation On Board EEPROM For User Program storage Stand alone operation with no connection to a PC Execution Halt/Branch pending switch closure Pre-wired for OptoSwitch inputs (see wiring diagram) Position Velocity and Torque modes Industry standard communications protocol Homes to an Opto or Encoder Index with a single command Fully programmable ramps and speeds Quadrature encoder based feedback for position mode Velocity mode possible with only Hall sensors for feedback Switch selectable device address Software selectable max currents 4MHz max encoder frequency Two 1 Amp On Off Drivers included Optional Step and Direction mode, 4MHz Step Frequency 4 ADC Inputs Halt / Branch on ADC Value Support Links

Home Drives Intelligent Stepper Driver All Motion Servo Drive

工业链是免费的公众性百科和搜索工具,收录展现海量信息,方便用户查找、认识和连接全球工业品,受众多用户支持、加入和上传,任何问题请联系工业链。

更多产品:

更多品牌:

对于国内有品牌官方销售机构的品类,建议直接咨询其国内机构;对于国内无官方销售机构、需从海外原厂采购的产品,或有相关问题,可联系工业链咨询了解;工业链非品牌官方原厂、代理商或办事处,仅按客户指定要求协助其从原厂或其授权代理采购原装产品,不代采任何品牌方不许可产品,网站制造品牌及其商标均归其权属人所有。